Skip to content Skip to sidebar Skip to footer

Dodge Ram 2500 Transmission Shifting Problems and How To Fix It

In this simple guide, we will tell you how to deal with the Dodge Ram 2500 transmission shifting problems.

The transmission is not shifting correctly in automatic transmission and a 5.2 l V8 engine.

The signs are frequently you can't shift at first gear no matter how much gas you give it.

In this case, the problem occurs because of a lousy governor pressure solenoid.

governor solenoid.
Governor solenoid

How To Fix Shifting Problems on Your Dodge Ram 2500

1. Check the Condition and The level of Transmission Fluid


The way you verify the transmission fluid volume level might be a little bit distinctive for each vehicle. So,  you check it with the engine warm and the transmission in park or neutral it.


You will get a more exact reading after you start the engine, and you put the transmission in two different gears. After that, wait five seconds between each gear, then you can stop the engine.

You can use a dipstick to check the fluid levels, whether the fluid is too much or less. If you observe the transmission fluid is pink, then it's in a good color. Another good sign is if you don't smell bad or anything.

So it isn't shocking when people have a transmission or even engine problems. The first thing they do is just put some oil in it, thinking that's the issue.

You don't want to see the color of the transmission fluid is dark. However, you also want to give the transmission fluid the old test.  It's a smell test, just looked it up in the manual smells. It's a bad sign if it smells burnt or simply unusual.

2. Use Scanner To Get Transmission Code


You can use a little scanner to get the code for the check engine, and you need the key to be in the on position. After that, the scanner will show you code (a transmission code) according to your repair manual. You can find the definition of that code. For example, governor pressure is not meet to target at 15 to 20 psi.

You will find the problem because the part that's responsible for governing the pressure inside your Dodge Ram transmission is a governor pressure solenoid. In this case, the sensor is responsible for sensing the pressure coming out of your governor solenoid.

You can say that the governor pressure solenoid output becomes less than 15 psi or greater than 30 psi, and this gives you trouble. So, if you have a Chrysler or a Dodge and you're having the same issue, you must find out the code for your transmission.

To get the governor solenoid, you need to drop the transmission pan. You're not going just to replace, but you'll get tips and tricks you can use when installing a new gasket, so you don't have any leaks later.

Next, remove five bolts on the pan and catch all the transmission fluid that's going to drip out, and after letting the drops of transmission fluid for five to ten minutes, you can remove the pan. You will need a Torx t20 socket to release two bolts that hold the transmission filter.

3. Clean the pan


You can use a scraper or some razor blades and remove as much of the previous gasket material from the pan as you can. Next, clean everything up with a brake cleaner and towels. It's super important the lip of the pan is completely clean and dry.

To address the areas where you have some bare metal showing, you can spray those areas with some epoxy paint and let it dry.

4. Remove Governor Body Out of  the Transmission


Furthermore, you must take out the governor solenoid body from the transmission. First, look at the connector for governor pressure solenoid. You have to take out the tab and then pull the connector out. Then, you require to pull out the red safety tab, but it will be easier to remove the governor's body first to get to the connector for the sensor.

To do that, you must remove four 11-mm bolts and two t20 screws. To take off the red safety tab, first, you need to push up on a little clip on the bottom and then, simultaneously, push the red tab out. When it out, just push on a little black tab on the connector, and you can pull it off.

Also, you can check the condition of the gasket for a governor's body. You can check, is it in excellent shape and stuck in a good position? If yes, then it should be fine to reuse.

5. Check the solenoid Condition


Alright, you get the governor's body out of the transmission. You have to take out the bracket on top of it, which is pinning it, just pull it out easily. Check the solenoid intake, usually it pretty much completely clogged up. But since you found these cheaply online, you are not going to risk it and prefer to simply clean and reinstall it back in the transmission.

Next, you need to take out the sensor and get some transmission fluid on the o-rings of your new solenoid. Put the bracket back on, get some transmission fluid on your new sensor, slide in, and they'll line up your bracket with your sensor. After that, push in your new solenoid until it fits into place, and you're about to put it back on the transmission.

6. Reinstall The Governor Solenoid


The installation has to be pretty much the reversal of removal. Just put the connector back in on the safety tab, make sure it clicks in place, and reinstall your connector for your solenoid.

Next, you can start all your screws and bolts by hand first and use a wrench on screws at least don't use an impact, do it carefully. After that, use a torque wrench to torque bolts down to a 100-inch pounds each. So, the screws are mainly here to keep down the bracket.

For the filter, just make sure you get some transmission fluid on the seal and hand tight is also ok.

7. Reinstall Painted Transmission Pan


Now you're ready to install a new gasket and newly painted transmission pan, and this is the part where anybody's got questions about how to do it properly.

So if you're reusing your old pan that it's not perfectly flat, you can always use the right RTV silicone that's made to be used in an automatic transmission. Note that substances in your automatic transmission fluid will quickly eat away at other RTV silicones.

The way you put RTV silicone is just basically put a bead down in the center, go around every bolt hole, all the way around the pan on the pan side. So you never put it on the transmission set because you simply don't need it.

If you're going to be using a new high-quality pan, then your problems are going to be less. But you want to use just a tiny amount of RTV around the corners that both helps seals it around and also holds in place your gasket. Make sure the gasket is nice and flat on the pan when you go to install, it's the most crucial thing when it comes to preventing leaks.

Also, you should check the bolt holes, and the metal around it should be completely flat before you put RTV Silicone. Sometimes people, when trying to stop leaks, will over-torque the pan bolts, and they'll bend the metal right around the bolt holes. If you find out such a case, just get something flat underneath it, gently tap it in, and make it even.

Next, the important part is laying down your new gasket. You want to make sure you lay down nice and flat as you can. Also, make sure you line up all the bolt holes exactly, and you ready put this back on.

First, you can utilize the two bolts on the sides down just by hand, so the pan is held in place. You don't want to run it down all the way, and you can move it just in case you need to make adjustments.

Next, you can give about 72-inch pounds and start from the center to the other side. You should wait an hour before you torque the bolts down to factory spec on the bar at 13 foot-pounds, and you can work from the center again.

Next, you should just wait another two or three hours or better let it sit overnight, and then you can refill with the new transmission fluid.

7. Refill The Transmission Fluid


According to the repair manual, in case you drop the trans pan, collect the fluid, air filter, you're only replacing about one and a half quarts of transmission lift. So that's how much you would need to add back into this transmission.

8. Start the Engine


Next, you can begin to start the engine and get the car up to operating temperature. Then you run the gear selector over all the gears, wait about five seconds between each gear, and you do this twice.

After that, control the trans fluid level, and you can add more transmission fluid if necessary.

Then you must check for leaks around transmission pan, and if there's no problem, then you can do the test drive and see if you fixed your shifting issue.

You have succeeded in repairing it if the shift from first gear to second gear and so on feels smooth.

Sometimes,  you require a more advanced scanner to read the codes from the transmission control module in your vehicle, and it's essential because that's how you're going to be able to recognize your transmission matter accurately.

Well, that's how to fix Dodge Ram 2500 transmission shifting problems, and hopefully, this information is useful for you.
Ryan Daniel
Ryan Daniel Ryan Daniel is a car enthusiast. Since owning his first BMW at a young age, he has loved the automotive world even more.